Basic Introduce
Constant Output EV Charger Power Module is a flexible, reliable and low-cost power module for EV supercharger.The Constant Output EV Charger Power Module is key power supply part of DC fast EV chargers, which converts AC to DC and charge electric vehicles or providing reliable DC supply for equipment requires DC power.
30KW Constant Output EV Charger Power Module has isolation function, strong anti-interference ability, self-contained protection function and easy integration. With the extensive use of semiconductor technology, packaging technology and high-frequency soft switches, the power density of module power supply is increasing, the conversion efficiency is higher and higher, and the application is simpler and simpler.
Product Features
- The EV charger power module working voltage: 285 ~ 475V AC
- The 30KW power module output voltage range: 200 ~ 1000V DC
- Single module up to 120A 30KW fast output speed
- Standby power consumption: < 12W
- Short circuit no damage
- Intelligent fan speed control
- The EV charger power module working temperature: -30 ~ +75°C
- Support parallel voltage and current regulation functions
- CE certificated
Technical Specification
Fan cooling
|
Electrical Ratings |
Input Voltage |
285 ~ 475V AC; 3-phase + PE |
|
Frequency |
45Hz - 55Hz |
|
|
Power Factor |
≥ 0.99 (Full Load) |
|
|
Output Power |
30KW |
|
|
Output Current |
120A (Max limit current is 120A, limit current point can be set between 2~120A) |
|
|
Output Voltage |
200 - 1000V DC |
|
|
Super Wide Constant power output Voltage range |
250 ~ 500VDC, 500 ~ 1000VDC |
|
|
Efficiency |
>95.5% (Full Load) |
|
|
Voltage stabilization Accuracy |
≤ ±0.5% |
|
|
Current stabilization Accuracy |
≤ ±1% (20% to 100% load) |
|
|
THD |
≤ 5% (More than 50% load) |
|
|
Soft Start Time |
3 ~ 8S |
|
|
HMI |
LED Light |
YES (indicate the work state) |
|
Operate handle |
YES |
|
|
Parts |
Connectors and Cables |
|
|
Communication |
Protocol |
CAN |
|
Environmental Ratings |
IP protection level |
IP20 |
|
Working Temperature |
Operating temp:-40~50℃ (≥55℃ with limitation power output) |
|
|
Storage Temperature |
Storage temp:-20~75℃ |
|
|
EV Charging Rectifier Cooling Method |
Fan cooling | |
|
Protections |
EV charger power module Protections |
Input over/under voltage protection, input over current protection, phase loss protection, Output over voltage protection, current limit protection, Output prevent reverse irrigation, Environment inspection & protection, Group sharing function, |
|
Compliance |
Complying to |
CE standard IEC 61851-1:2010 / EN 61851-1:2011 IEC 61851-23:2014 / EN 61851-23:2014 IEC 61851-21-2:2018 2014/35/EU (Low Voltage) 2014/30/EU (Electromagnetic Compatibility) |
What is output prevent reverse irrigation?
When the external voltage is higher than the output voltage of charging module, it will not cause damage to the module.
What is Group sharing function?
Grouping modules is supported in the system. When grouping output, the module output power lines are required to be isolated from each other. Only CAN bus is connected between each module. The output voltage and current can be controlled independently between each group of modules, which can realize grouping current balance sharing output. It is suggested that the number of modules in each group≤24.
How to Maintenance and replacement the EV charger power module of Superchargers ( All type CCS CHAdeMO GBT etc fast chargers)?
1.The dust-proof net of the cabinet should be cleaned and dusted regularly to avoid dust accumulation at the air inlet, which will lead to high internal temperature of the module
2 in case of unrecoverable failure, please replace the module directly
-Module without hanging ears: rotate the module lock to the open state, hold the handle with one hand, drag the module with the other hand, slowly take out the module, slowly push the new module into the insertion frame, and then rotate the new module lock to the locked state.
-Module with lugs: rotate the module lock to the open state, loosen the lug screw, hold the handle with one hand, drag the module with the other hand, slowly take out the module, slowly push the new module into the insertion frame, rotate the new module lock to the locked state, and tighten the lug screw.
